Elinchrom 500 Manuel d'utilisateur télécharger pdf (Page 2)

UmbrellasUmbrellas

Umbrellas

An umbrella with a 7 mm shaft may be used with the unit, by opening the umbrella

and inserting the end of the shaft into the umbrella tube (10) while holding the unit with

the other hand.

The tube contains a spring which holds the umbrella firmly in place. The correct position

of the umbrella must be adjusted so that the position of the light from the reflector

coincides with the edge of the umbrella.

NOTE : the diameter of the umbrella socket is designed to suit Elinchrom or ProlincaNOTE : the diameter of the umbrella socket is designed to suit Elinchrom or Prolinca

NOTE : the diameter of the umbrella socket is designed to suit Elinchrom or Prolinca

umbrellas only and the use of other shaft sizes may cause damage to the unit.umbrellas only and the use of other shaft sizes may cause damage to the unit.

umbrellas only and the use of other shaft sizes may cause damage to the unit.

An alternative umbrella clamp is attached to the tilt clamp handle which accepts

umbrellas of other manufacturers.

The umbrella is removed by grasping the shaft firmly and withdrawing it from the

umbrella tube while holding the unit with the other hand. Care should be taken to

avoid striking the flashtube with the end of the shaft on removal.

When the unit is used with some larger lightshapers, the unit fits inside the lightshaper

which itself is supported on a stand. In this case, the unit is fixed into the mountig ring by

using the handle to rotate (clockwise) the unit in place. Once again it is important to

secure the flash using the locking ring.

Flash powerFlash power

Flash power

As soon as the power unit is switched on, it charges to the set power and the green

'ready' lamp (5) lights to show that the unit is charged and ready to fire.

The power level is controlled by the flash variator (7). This is continuously variable of

3 f-stop, from the full power to 1/4th.

When reducing power, a manual flash should be fired by pressing the open flash

button (5). This dumps the extra power and allows the unit to recycle to the lower level

selected. When the modelling lamp is switched on, the power level is controlled by the

power control (8). This is continuously variable on 3 f-stop, from the full to 1/4th.

*The EL 750 and EL 1500S, provides continuously variable adjustment of 5 f-stop, from the full

power to 1/16th. This units have an integrated discharge system. In order to restrict the heating of

the unit, we suggest to release a flash with the green test button (5), after each strong reduction

of power (more the 2f-stop).

This allows to release the excess of energy in the flash tube, you will gain time and extend the life

span of your compact units.

Modelling lampModelling lamp

Modelling lamp

The lamp is switched on using the modelling lamp

switch (4). The Krypton E27 modelling lamp is specially

designed for the Elinchrom units.

Note :Note :

Note :

the other lamps may touch the flash tube and

either may break.

There are some alternatives available and your

authorized Elinchrom dealer can advise which can

be used.

*The EL 750S - 1000 - 1500S are fitted with a 200W

halogen lamp. It is vital that the correct fuse (2 amp

flink) is fitted in the modelling lamp fuse holder when

this lamp is being used.

ControlsControls

Controls

1. Mains inlet socket with spare fuse

2. Mains fuse (slow blow)

3. Illuminated mains on/off switch

4. Modelling lamp switch

5. Open flash «Test» and ready

6. Slave cell on/off

7. Stepless sliding flash variator

8. Stepless modelling lamp control

9. Synchro-socket

10.Umbrella tube

Flash tube

Modelling

lamp

Umbrella tube (10)

(entry point)

Tilthead with locking

umbrella holder

Locking Ring

Setting UpSetting Up

Setting Up

Your flash unit should only be used while mounted to a light

stand or some similar secure support.

The unit will fit onto any 5/8th inch spigot and is held at the

required angle by tightening the clamping handie. The front

end of the head has a bayonet fitting and locking ring

which holds the protective cap in place and allows

reflectors and other accessories to be fitted during use.

DO NOT operate the unit without first removing the blackDO NOT operate the unit without first removing the black

DO NOT operate the unit without first removing the black

protective cover.protective cover.

protective cover. To remove the protective cap, rotate the

locking ring, so that the white dot, on the ring, lines up with

that on the bayonet. This un-locks the bayonet and allows

the protective cap to be removed by twisting anticlockwise.

Fitting the reflector is the reverse of this operation. When

fitted to the unit, all attachments should be locked in place

by turning the locking ring so that the two white dots are

about 2 cm apart.

Operating instructionsOperating instructions

Operating instructions

The mains cable is connected to the mains inlet (1)

on the control panel.

The fuse holder (2) contains a mains fuse (together

with a spare fuse).

The unit may now be switched on using the mains

on-off switch (3). This will illuminate showing that

power is present.

SynchronisationSynchronisation

Synchronisation

The flash may be triggered in a number of ways.

Manual flashes may be triggered by using the green open flash switch ( 5 ) which

incorporates the ready lamp, for testing, metering, etc.

Synchronisation with the camera is achieved by using a synch cable, which connects

the flash synch socket (9) to the standard flash connector on the camera or direct to

the hot shoe using an adapter.

If more than one unit is in use, additional units may be synchronised to the first using

the built-in photocell (6). This is switchable, and operates when the transparent

square button is raised. The remote photocell of the unit picks the flash from the main

unit and fires the unit at the same instant, avoiding the need for synch cable linking

all the units.

For more demanding applications, a variety of accessories is available such as

extension synch cables, remote photocells and radio release links.

An indicator lamp above the photocell indicates whether it is switched on (green) or

off (red).

1 2

Commentaires sur ces manuels

Pas de commentaire

Elinchrom 500 Manuel d'utilisateur Page 2

Commentaires sur ces manuels